How to use the Mic Test
- Click Start mic test and choose Allow when your browser asks for microphone access.
- Speak normally, clap or tap the mic. The level meter and waveform should move, and the status turns green.
- If you have several microphones (laptop, headset, webcam), pick one from the Microphone list to test it.
- Press Record 5 seconds and listen to the playback to hear how you sound to others.
- Press Stop when you are done — the microphone is released immediately.
How this online mic test works
When you press Start, the browser asks for permission and opens your microphone with the standard getUserMedia API. The audio is routed into a Web Audio AnalyserNode, which hands the page about 2,000 raw samples on every screen refresh. From those samples the tool calculates two numbers:
- RMS level — the root-mean-square of the samples, which tracks perceived loudness. It drives the meter, “Current level” and “Average”.
- Peak level — the largest single sample, used for the peak readout, the waveform and clipping warnings.
Levels are shown in dBFS (decibels relative to full scale), so 0 dB is the loudest value a digital signal can hold and everything else is negative. This is not the same as the dB SPL you would read on a sound-level meter; it describes how hot the signal is inside your computer. Nothing is sent to a server — the analysis runs entirely in your browser tab.
Reading the results
| Level (dBFS) | What it means |
|---|---|
| Below −60 | Silence or room noise only. If you are talking, the mic is muted, far away or the wrong device. |
| −40 to −20 | Quiet speech. Usable, but others may need to turn you up. |
| −20 to −6 | A healthy speaking level for calls and voice recording. |
| −6 to −1 | Loud. Fine for short peaks such as laughter. |
| Near 0 | Clipping — the waveform is cut off and sounds distorted. Lower the input gain. |
The tool also watches for problems. If the browser receives pure digital silence (every sample exactly zero) for three seconds, the microphone is almost certainly muted by a hardware switch, a headset mute button or the operating system. If a faint signal arrives but nothing rises above about −50 dB, you will see “No sound detected” instead, which usually points to low input volume or the wrong device.
Microphone not working? Troubleshooting checklist
1. Browser permission
Click the padlock or the camera/mic icon at the left of the address bar and set Microphone to Allow, then reload. In Chrome and Edge you can also open Settings → Privacy and security → Site settings → Microphone. In Firefox, look under Settings → Privacy & Security → Permissions. Safari keeps the setting under Settings → Websites → Microphone. If you clicked “Block” once, the browser will not ask again until you change this.
2. Windows privacy settings
On Windows 10 and 11, open Settings → Privacy & security → Microphone. Make sure “Microphone access” is on and that desktop apps (which includes your browser) are allowed to use it. Then open Settings → System → Sound, pick the correct input device and check that its volume is not at zero.
3. macOS privacy settings
Open System Settings → Privacy & Security → Microphone and enable the switch for your browser. macOS only applies the change after you quit and reopen the browser. In System Settings → Sound → Input you can select the device and raise the input volume.
4. Hardware and other apps
- Check for a mute switch on the headset cable, earcup or USB mic, and a mute key (often F4 or a microphone icon) on laptops.
- Re-plug USB and 3.5 mm connectors. Many laptop jacks need a 4-pole (TRRS) plug to carry a headset mic.
- Close Zoom, Teams, Discord or recording software. Some drivers let only one app open the mic at a time, which shows up here as “could not be opened”.
- Bluetooth headsets switch to a lower-quality “hands-free” profile when the mic is in use — this is normal and explains muffled playback.
Why does my recording sound different?
Browsers apply echo cancellation, noise suppression and automatic gain control by default, as video-call apps do. They make speech clearer on calls but can make music or quiet sounds pump and fade. Open “Audio processing” and switch them off to hear the raw signal from your microphone. Changing a setting restarts the test with the new options. Some built-in laptop mics and operating systems apply their own processing that a web page cannot disable.
Privacy
This mic test does not record, store or upload anything. The 5-second clip is created only when you press Record, lives in this tab’s memory and is discarded when you leave the page. Stopping the test, switching tabs or closing the page releases the microphone, so your browser’s recording indicator goes away. Want to check your camera too? Try the webcam test.
Frequently asked questions
How do I test my microphone online?
Is this mic test safe and private?
Why does it say “No signal”?
What is a good microphone level in dB?
Why are the microphone names not shown at first?
My mic works here but not in Zoom or Teams. Why?
Last reviewed November 2026. Results are estimates for information only — see our disclaimer.