How to use the Ohm’s Law Calculator
- Choose a mode: V · I · R · P for Ohm’s law, Series / parallel to combine resistors, or Energy & bill for kWh units and cost.
- In Ohm’s law mode, type any two of voltage, current, resistance and power, pick the unit prefix (mA, kΩ, kW and so on), and leave the other two boxes empty.
- Read the other two quantities instantly. The formula wheel highlights the formulas used and the working panel shows each substitution.
- For resistor networks, add up to 10 resistors and read the series and parallel equivalent resistance with the steps.
- For a bill, enter the appliance wattage, hours per day, number of days and your price per unit to get kWh and the cost.
Ohm’s law and the power formula
Ohm’s law says that the current through a conductor is proportional to the potential difference across it, provided its temperature and other physical conditions stay the same. The constant of proportionality is the resistance. Combined with the definition of electric power, it gives four linked quantities. Know any two and you can find the other two.
Here V is the potential difference in volts (V), I is the current in amperes (A), R is the resistance in ohms (Ω) and P is the power in watts (W). These are the same relations used in the NCERT Class 10 chapter Electricity and the Class 12 chapter Current Electricity.
The VIR triangle and the formula wheel
The VIR triangle puts V on top and I × R on the bottom. Cover the quantity you want: cover V and you see I × R, cover I and you see V over R. The formula wheel above extends this to power. Each quarter holds one quantity, and its outer ring lists the three ways to calculate it from any pair of the others, which makes 12 formulas in total. The calculator highlights the formulas it used for your inputs.
Worked example
A 12 V battery is connected to a 4 Ω resistor. Find the current and the power.
- I = V ÷ R = 12 ÷ 4 = 3 A
- P = V² ÷ R = 144 ÷ 4 = 36 W (check: V × I = 12 × 3 = 36 W)
Now a 60 W bulb rated for 230 V: I = P ÷ V = 60 ÷ 230 ≈ 0.261 A (261 mA) and R = V² ÷ P = 52,900 ÷ 60 ≈ 881.7 Ω. That is its hot resistance; a filament’s resistance is much lower when cold, because resistance rises with temperature.
Unit prefixes
| Prefix | Factor | Example |
|---|---|---|
| µ (micro) | 10−6 | 50 µA = 0.000 05 A |
| m (milli) | 10−3 | 20 mA = 0.02 A; 500 mV = 0.5 V |
| k (kilo) | 103 | 4.7 kΩ = 4,700 Ω; 2 kW = 2,000 W |
| M (mega) | 106 | 1 MΩ = 1,000,000 Ω |
The most common exam slip is mixing prefixes, for example dividing volts by kilo-ohms and calling the answer amperes. Convert to base units first, as the working panel does, and the answer comes out in A, V, Ω or W.
Resistors in series and parallel
In series the same current flows through every resistor and the voltages add, so resistances add. In parallel every resistor has the same voltage and the currents add, so the reciprocals add. The parallel result is always smaller than the smallest single resistor. For two resistors, R_eq = R1R2 ÷ (R1 + R2). For example, 100 Ω, 220 Ω and 470 Ω give 790 Ω in series and about 59.98 Ω in parallel. Need the value of a real resistor first? Read its bands with the resistor colour code calculator.
Electrical energy and your bill
Energy is power multiplied by time. Electricity boards charge per unit, and one unit is one kilowatt-hour (kWh), which equals 3.6 × 106 J.
Example: a 1,000 W heater used 8 hours a day for 30 days uses 1000 × 8 × 30 ÷ 1000 = 240 kWh. At 8 per unit that is 1,920 in your currency. This matches the typical Class 10 question “find the cost of running an appliance”. Your actual bill also includes fixed charges, slab pricing and taxes set by your supplier, so use this as the energy part only.
Common mistakes and exam tips
- Using Ohm’s law where it does not apply. Diodes, LEDs and filament lamps are non-ohmic: their V–I graph is not a straight line, so R = V ÷ I gives only the resistance at that one operating point.
- Forgetting to square. P = I²R and P = V²/R both square the current or voltage. Doubling the voltage across a fixed resistor quadruples the power.
- Adding parallel resistors directly. Add the reciprocals, then take the reciprocal of the total.
- Watts vs watt-hours. Watts measure the rate of energy use; kWh measure the energy used. Bills are in kWh.
- For energy in joules (W = Pt, or W = VIt = I²Rt), see the work, energy and power calculator.
Frequently asked questions
What is Ohm’s law in simple words?
How do I calculate current from voltage and resistance?
How do I calculate power from current and resistance?
Why is the equivalent resistance in parallel less than the smallest resistor?
What is 1 unit of electricity?
Does Ohm’s law apply to all materials?
Last reviewed November 2026. Results are estimates for information only — see our disclaimer.