Roof Pitch Calculator

Convert between roof pitch, angle and slope, then work out rafter length, ridge height and the true roof area from the building footprint.

Free, no sign-upRuns in your browserUpdated November 2026
I know the…
Use the same unit for both, e.g. inches of rise per 12 inches of run.
Rafters & roof area
ft
ft
ft
Area assumes a gable or hip roof with one pitch on every plane and the overhang on all sides.
Roof pitch
—
Angle
—
Slope (grade)
—
Pitch multiplier
—
Rise : run ratio
—
Rafter length
—
Ridge height above walls
—
Roof area
—
Roofing squares
—

Roof pitch table
PitchAngleSlope %MultiplierRafter per 12 in run

How to use the Roof Pitch Calculator

  1. Choose what you know: rise & run, the pitch as x/12, or the roof angle in degrees.
  2. Read the pitch, angle, slope percentage and pitch multiplier. The diagram shows the slope to scale (very steep pitches are clipped).
  3. Enter the building length, width (span) and eave overhang to get rafter length, ridge height and the true roof area.
  4. Use the pitch table to compare common pitches from 1/12 to 12/12.

What roof pitch means

Roof pitch is how steep a roof is, written as the inches of vertical rise for every 12 inches of horizontal run. A 6/12 roof (said "six-twelve" or "6 in 12") rises 6 inches for each foot it travels inward. The same steepness can be given as an angle in degrees or as a percentage slope. This calculator converts between all three.

Pitch (x/12) = rise ÷ run × 12 Angle (°) = arctan(rise ÷ run) Slope (%) = rise ÷ run × 100 Multiplier = √(1 + (pitch ÷ 12)²) Rafter length = (span ÷ 2 + overhang) × multiplier Roof area = footprint area (incl. overhangs) × multiplier

To go from an angle back to pitch, use pitch = 12 × tan(angle). For example, a 30° roof is 12 × tan 30° ≈ 6.93/12.

Worked example

A house is 40 ft long and 30 ft wide with a 6/12 roof and 1 ft overhangs. The angle is arctan(6 ÷ 12) = 26.57° and the slope is 50%. The multiplier is √(1 + 0.5²) = 1.118.

  • Rafter length: the run of each rafter is half the span plus the overhang, 15 + 1 = 16 ft. 16 × 1.118 = 17.89 ft, measured along the slope before any ridge-board or plumb-cut adjustments.
  • Ridge height: 15 ft × 6/12 = 7.5 ft above the top of the walls.
  • Roof area: the footprint with overhangs is 42 × 32 = 1,344 sq ft. 1,344 × 1.118 ≈ 1,503 sq ft, or about 15.03 squares (1 roofing square = 100 sq ft).

Roof pitch to degrees chart

PitchAngleMultiplierPitchAngleMultiplier
1/124.76°1.00357/1230.26°1.1577
2/129.46°1.01388/1233.69°1.2019
3/1214.04°1.03089/1236.87°1.2500
4/1218.43°1.054110/1239.81°1.3017
5/1222.62°1.083311/1242.51°1.3566
6/1226.57°1.118012/1245.00°1.4142

A 12/12 roof is exactly 45°, with a slope of 100%. Slope percentage and angle are not proportional: a 100% slope is 45°, not 90°.

Why the multiplier works for hip roofs too

Every plane of a roof with a single pitch is tilted by the same angle, so its true area equals its plan (bird's-eye) area divided by the cosine of that angle. That is the same as multiplying by √(1 + (pitch/12)²). It holds whether the roof is a simple gable or a hip roof, as long as all planes share one pitch. Dormers, valleys with different pitches, and roofs with mixed slopes have to be calculated plane by plane.

How to measure your roof pitch

  • From the attic: hold a level horizontally against the underside of a rafter. Mark 12 inches along the level, then measure straight up from that mark to the rafter. That measurement is the rise per 12.
  • On the roof: place a level on the shingles, lift the downhill end until it is level, and measure the gap at 12 inches. Only do this with proper fall protection.
  • From plans or a phone app: drawings usually state the pitch, and inclinometer apps give an angle you can convert here.

Practical notes

  • Roofing material limits depend on pitch. In US practice, asphalt shingles generally need at least 2/12, with extra underlayment on low slopes. Follow the manufacturer's instructions and your local building code.
  • Steeper roofs shed water and snow better but cost more to build and are harder to work on safely.
  • When ordering materials, add waste for cuts, starter rows, hips and ridges. Ask your supplier what allowance to use for your roof's shape.
  • For flat areas such as decks or floors, use the square footage calculator.

Frequently asked questions

How do I calculate roof pitch?
Divide the rise by the run and multiply by 12. A roof that rises 4 ft over a 12 ft run has a pitch of 4 ÷ 12 × 12 = 4/12. In degrees that is arctan(4 ÷ 12) ≈ 18.43°.
What angle is a 6/12 roof pitch?
A 6/12 pitch is about 26.57°: arctan(6 ÷ 12) = arctan(0.5). Its slope is 50% and its pitch multiplier is 1.118.
How do I convert degrees to roof pitch?
Pitch = 12 × tan(angle). For 30°, 12 × 0.5774 ≈ 6.93, so the pitch is about 6.9/12. Select “Angle” above to convert any angle.
What is a roof pitch multiplier?
It is the factor that converts a flat footprint area or horizontal run into the true sloped length or area: √(1 + (pitch ÷ 12)²). For 6/12 it is 1.118, so 1,000 sq ft of footprint becomes about 1,118 sq ft of roof.
How do I calculate rafter length?
Take half the building span, add the overhang, and multiply by the pitch multiplier. For a 30 ft span with a 1 ft overhang at 6/12: (15 + 1) × 1.118 ≈ 17.89 ft. Adjust for the ridge board and cuts.
What is the most common roof pitch?
Many houses have pitches in the conventional range of roughly 4/12 to 9/12, which suits asphalt shingles and sheds water well. The right pitch depends on climate, roofing material, style and local code.

Last reviewed November 2026. Results are estimates for information only — see our disclaimer.

Related tools

All everyday tools