Speaker Test

Check that your speakers or headphones are wired correctly and working across the full range: left and right channels, a stereo pan, a frequency sweep and an in-phase vs out-of-phase test.

Free, no sign-upRuns in your browserUpdated November 2026
Now playing
Nothing
Choose a test below. Start with the volume low.
1. Left / right channels
Plays a short chime and noise bursts on the chosen side only. The spoken label comes from both speakers, because browsers cannot route speech to one channel.
2. Stereo pan sweep
Pink noise glides from left to right and back.
3. Bass & treble sweep (20 Hz → 20 kHz)
A sine tone rises over 20 seconds.
4. Phase / polarity
In phase should sound centred and full. Out of phase should sound wide, vague and thin in the bass.

5.1 and 7.1 surround: web browsers normally mix everything down to stereo, so this page tests the front left and right outputs only. Centre, surround and subwoofer channels are best checked with the test tones in your AV receiver or the operating system’s speaker setup.

How to use the Speaker Test

  1. Set the test volume low, then press Left, Right and Both. Each sound should come only from the side named.
  2. Play the pan sweep. The noise should glide smoothly from the left speaker to the right and back, with no gaps or jumps.
  3. Play the bass & treble sweep and press Mark this frequency when the tone becomes audible and again when it disappears.
  4. Compare In phase with Out of phase. In phase should sound fuller and centred; if not, one speaker is wired backwards.
  5. Press Stop all sound when you are done.

What this speaker test checks

This page plays four kinds of test signal, all generated live in your browser with the Web Audio API. Nothing is downloaded, and you can use it with laptop speakers, desktop monitors, a soundbar, Bluetooth speakers or headphones.

  1. Left / right channels reveal swapped cables, a dead speaker or earcup, or a balance setting pushed to one side.
  2. Pan sweep shows whether the stereo image is even: the sound should move smoothly across without dropping out or sticking to one side.
  3. Frequency sweep shows the range your speakers (and ears) can reproduce, and exposes rattles, buzzes and room resonances.
  4. Phase / polarity checks that both speakers push air in the same direction at the same time.

1. Left and right channel test

Each button plays a rising three-note chime followed by three bursts of pink noise on the selected side only. If voice announcements are available, your browser first says “Left”, “Right” or “Both channels”. That voice always comes from both speakers, because web speech synthesis cannot be routed to one channel; the chime and noise that follow are the actual test.

If the left test comes from the right, your cables or headphones are reversed (or the headphones are on backwards; check the L and R marks). If one side is silent, check the cable, the speaker’s own power and volume, and your system’s balance control: Windows has it under Sound → Output device → Properties, and macOS under System Settings → Sound → Output. “Both” should sound like it comes from a point exactly between the speakers; if it leans to one side, the balance or the speaker volumes differ.

2. Stereo pan sweep

Pink noise is moved from hard left to hard right and back twice over 16 seconds, using the browser’s equal-power pan law (the sum of the squared channel gains stays constant, so loudness does not dip in the middle). The bar under “Now playing” shows where the sound should be. A hole in the middle usually means the speakers are too far apart; a sound that jumps suddenly suggests one channel is much louder than the other.

left gain = cos(x), right gain = sin(x), where x = (pan + 1) × π/4

3. Bass and treble sweep

A sine tone rises from 20 Hz to 20,000 Hz over 20 seconds on a logarithmic scale, so each octave gets the same time (about two seconds). Press Mark this frequency when you first hear the tone and again when it fades away at the top. Typical results:

DeviceTypical low-frequency limit
Phone or laptop speakersAbout 150–300 Hz; little real bass
Small desktop speakersAbout 70–100 Hz
Good headphones20–40 Hz is often audible
Hi-fi with a subwooferDown to about 20–35 Hz

These are rough guides; output depends on the model, volume and how close you are. At the top end, most adults stop hearing the tone somewhere between 12 and 17 kHz, which is normal age-related change, not a speaker fault. Listen for buzzing or rattling during the bass part: it often comes from loose objects, a damaged driver or a cabinet panel, not the signal. For a steady tone at a single frequency, use the tone generator.

4. Phase (polarity) test

Every speaker has a positive and a negative terminal. If one speaker’s wires are swapped, it moves inward while the other moves outward, so their bass cancels. In the in-phase test both channels play the same noise. In the out-of-phase test the right channel is inverted. With correct wiring, in phase sounds focused, centred and full; out of phase sounds wide and vague, as if coming from around your head, with weak bass. If the out-of-phase test sounds more solid, check the red/black (or +/−) wires on one speaker. The test is most obvious with two speakers facing you; on headphones the difference is subtler.

Surround sound (5.1 and 7.1)

Browsers usually output audio as stereo, and most operating systems mix web audio down to two channels, so this page cannot drive the centre, surround or LFE (subwoofer) channels individually. To check a surround system, use the built-in test tones of your AV receiver, or the speaker configuration panel in Windows (Sound → Configure) or Audio MIDI Setup on macOS. If your subwoofer handles bass from the front speakers through bass management, it will still play the low part of the sweep above.

Testing a microphone instead? Use the mic test.

Frequently asked questions

How do I test my left and right speakers?
Turn the volume down, press Left, then Right. Each chime and noise burst should come only from the side named. If they are swapped, your cables or headphones are reversed; if one side is silent, check the cable and the system balance setting.
Why does the voice say “left” from both speakers?
Browser speech synthesis always plays through the normal output and cannot be sent to a single channel. The voice only announces the test; the chime and noise bursts that follow are played on the selected side only.
How can I tell if my speakers are out of phase?
Play the in-phase and out-of-phase tests. With correct wiring, in phase sounds centred with solid bass and out of phase sounds diffuse and thin. If it is the other way round, one speaker has its + and − wires swapped.
Why can’t I hear the lowest part of the bass sweep?
Most laptop, phone and small desktop speakers cannot reproduce frequencies below roughly 80–200 Hz. Try headphones or speakers with a subwoofer. Keep the volume moderate so you do not damage small drivers.
Can I test 5.1 or 7.1 surround sound here?
Not channel by channel. Browsers normally mix web audio to stereo, so only the front left and right channels can be tested. Use your AV receiver’s test tones or the operating system’s speaker setup for surround channels.
Does this speaker test work with Bluetooth headphones?
Yes. All tests work with Bluetooth, though Bluetooth adds a small delay, so the on-screen label may move slightly ahead of what you hear.

Last reviewed November 2026. Results are estimates for information only — see our disclaimer.