Mouse Test

Click, scroll and move inside the test area to check every button, catch a mouse that double-clicks on its own, spot a skipping scroll wheel and estimate the polling rate.

Free, no sign-upRuns in your browserUpdated November 2026
Click, scroll and move inside the test area
Left
Not tested
0
Middle
Not tested
0
Right
Not tested
0
Back
Not tested
0
Wheel
▲ 0 · ▼ 0
Forward
Not tested
0

The right-click menu, middle-click autoscroll, page scrolling and back/forward navigation are blocked inside this box only.

Double-click (chatter) test
Chatter faults
0
Last gap (same button)
—
Shortest gap
—
Double-clicks (OS)
0
    Single-click one button slowly for 30–60 seconds. Any press within the threshold of the previous press of the same button is flagged.
    Scroll, polling & clicks
    Scroll skips
    0
    Total clicks
    0
    Polling rate (now)
    —
    Polling rate (peak)
    —
    Move the mouse quickly in circles inside the test area for a few seconds. Polling rate is an estimate from browser events.
    Everything runs on this page only. No clicks or movements are recorded or sent anywhere.

    How to use the Mouse Test

    1. Point at the test area and press each button: left, middle (wheel click), right, and the two side buttons Back and Forward. Each tile turns green once it works.
    2. For the double-click test, single-click one button at a normal pace for 30–60 seconds. Any press flagged in red came too soon after the previous one.
    3. Scroll the wheel slowly in one direction. The ▲/▼ trail should be one colour; red arrows mark sudden direction flips (scroll skipping).
    4. Move the mouse quickly in circles inside the area to see the estimated polling rate and its peak.
    5. Press Reset to start again. Outside the box the page scrolls and right-clicks as normal.

    What this mouse test checks

    This tester listens to the browser’s mousedown, mouseup, wheel and pointer-movement events inside the test area and shows exactly what your computer receives. It covers the five buttons browsers can see — left, middle (pressing the wheel), right, and the side buttons usually used as Back and Forward — plus the scroll wheel and the rate at which movement events arrive.

    Buttonevent.buttonTypical use
    Left0Primary click
    Middle (wheel click)1Open link in new tab, autoscroll
    Right2Context menu
    Back (side, rear)3Browser back
    Forward (side, front)4Browser forward

    Extra buttons such as DPI switches, sniper buttons or programmable macro keys are usually handled by the mouse or its software and are not reported to the browser as buttons, so they cannot be tested on a web page. If you have remapped buttons in the manufacturer’s software or in your operating system, the tester shows what they are mapped to, not their physical position.

    How to test a mouse for double clicking

    A worn or dirty switch can “bounce” or chatter: one physical press is reported as two clicks a few milliseconds apart. Files open when you meant to select them, drag-and-drop lets go, and in games a single shot becomes two. The tester records the time of each press of a button and compares it to the previous press of the same button:

    Chatter fault if (time of this press − time of previous press of the same button) < threshold (default 80 ms)

    A deliberate fast double-click by a person usually has a gap of well over 80 ms, while switch bounce typically produces much shorter gaps. To test, single-click slowly and steadily for 30–60 seconds. If faults appear even though you only clicked once each time, the switch is likely failing. You can raise the threshold to catch borderline cases or lower it if you click very fast. The Double-clicks (OS) counter is separate: it counts the browser’s own dblclick events, which use your operating system’s double-click speed setting.

    Fixes for a double-clicking mouse

    • Test on another computer or USB port to rule out software. If it chatters everywhere, it is the hardware.
    • Blow compressed air around the button edge; dust can cause intermittent contact.
    • Check the manufacturer’s software for a debounce time setting. A slightly higher value can hide mild chatter.
    • If the mouse is under warranty, chatter is a common, recognised fault — keep a screenshot of the fault log.
    • Replacing the micro-switch is possible on many mice but involves soldering.

    Scroll wheel test and scroll skipping

    The wheel counter shows how many wheel events arrived in each direction. A healthy wheel scrolled steadily in one direction produces a single colour of arrows. A dirty or worn wheel encoder often produces the occasional event in the opposite direction, so the page jumps back while you scroll. The tester flags any direction change that happens within 100 ms of the previous wheel event as a scroll skip, because it is very hard to reverse a wheel that fast on purpose. Touchpads and “free-spin” or smooth-scrolling wheels send many small events, which is normal; look for red arrows rather than the raw count.

    Polling rate estimate

    Polling rate is how often the mouse reports its position to the computer: 125 Hz (every 8 ms) on many office mice, 500 or 1000 Hz on most gaming mice, and 2000–8000 Hz on some newer models. The tester counts pointer events while you move — using pointerrawupdate where the browser supports it, or the coalesced events of pointermove otherwise — and divides by the elapsed time.

    Estimated polling rate (Hz) = (number of movement events − 1) × 1000 ÷ time span in ms

    This is an estimate. A report is only sent when the mouse moves, so slow movement reads low; move quickly and look at the peak. Browsers, operating systems and wireless receivers can also merge or limit events, and very high rates (4000–8000 Hz) are often under-reported in a browser. Treat a peak near 1000 Hz as confirmation that a 1000 Hz setting is active, not as a precise measurement.

    Click counter and touch screens

    The total click counter adds up every button press in the area. For a timed clicking challenge use the CPS test. On phones and tablets, tapping counts as a left click, but right-click, the wheel and polling rate need a real mouse. When you are done, check the rest of your setup with the keyboard tester and the refresh rate test.

    Frequently asked questions

    How can I tell if my mouse is double clicking?
    Single-click one button slowly for about a minute inside the test area. If the chatter fault counter goes up even though you clicked once each time, the switch is sending two clicks for one press — a classic double-click fault.
    Why do the back and forward buttons not show?
    Most browsers report them as buttons 3 and 4, and the tester blocks the navigation inside the test area. If they still do nothing, the mouse software may have remapped them to another action, or the mouse may not send them as standard buttons.
    How accurate is the polling rate test?
    It is an estimate based on how many movement events the browser receives per second while you move. Move quickly and read the peak. Browsers may merge events, so very high rates such as 4000 or 8000 Hz often read lower than the true setting.
    What is a good polling rate for a mouse?
    1000 Hz (a report every 1 ms) is the common standard for gaming mice. 125 Hz is typical for office mice and is fine for everyday work. Higher rates use more CPU and, on wireless mice, more battery.
    What is scroll skipping?
    It is when the page jumps the wrong way for a moment while you scroll steadily. It usually comes from a dirty or worn wheel encoder. The tester marks quick direction reversals in red.
    Does the right-click menu still work on the rest of the page?
    Yes. The context menu, middle-click autoscroll and page scrolling are only blocked inside the test box so that every button and wheel movement can be measured.

    Last reviewed November 2026. Results are estimates for information only — see our disclaimer.